COMMANDER FOR RENAULT 5.3

The Commander for Renault is a professional software mainly for programming the new key/card of Renault vehicles.

ALL OTHER COMMANDERS SOFTWARES CAN BE ADDED TO THE SAME AVDI

ALSO ORIGINAL SOFTWARES LIKE STAR DIAGNOSE /GT

               PIN code not needed 

Functions:

• Connecting with all electronic control modules in the vehicle. Working by K and CAN bus diagnostic connection.
• For all electronic control units reading identification data
• For all electronic control units read and clear error (DTCs)
• For all electronic control units live data (measured values)
• For all electronic control units coding/configuration
• For all electronic control units actuator tests
• Airbag crash data clear Dacia Logan/Duster by OBDII
• Program ID in UCH module
• Mileage recalibration in Instrument cluster - Laguna III, Megane III, Fluence, Master III, Scenic III, Scenic/Modus (2003-2004), Clio II, Kango by OBDII
• Odometer correction for Renault Clio/Kango/Meganne with HC908 JAEGER
• Key programming function / pin code reading : 

- Megane II X84 2003-2006
- Renault Megane II Ph2 X84 2007+
- Renault Megane III X95 2009+
- Renault Scenic II X64 2003+
- Renault Scenic II Ph2 X64 2007+
- Renault Scenic III X95 2009+
- Renault Laguna II X56 2000-2005
- Renault Laguna II Ph2 X74 2005-2007
- Renault Laguna III X91 2007+
- Renault Valsatis X73 2002+
- Renault Valsatis Ph2 X73 2006+
- Renault Espace IV X81 2003-2006
- Renault Espace IV Ph2 X81 2006+
- Renault Master Ph2 X70 2002-2006
- Renault Master Ph3 X70 2007+
- Renault Traffic II X83 2002-2006
- Renault Traffic II Ph2 X83 2007+
- Renault Kango MUX Ph2 X76 2002-2007
- Renault Kango X61 2008+
- Renault Clio II Ph2/3 X65 2002-2006
- Renault Clio Symbol
- Renault Clio Symbol 2010+ (BCM JC)* (check the footnote) 
- Renault Clio Thalia
- Renault Clio Campus 
- Renault Clio Sedan
- Renault Clio Classic
- Renault Clio III 2005+
- Renault Clio III with key card
- Renault Modus 2004+
- Renault Grand Modus 2008+ 
- Renault Master III X62 2010+
- Dacia Duster 2010+ (BCM JC) * (check the footnote )
- Dacia Logan X90 2004-2008
- Dacia Logan Ph2 X90 2008+
- Dacia Logan 2010+ (BCM JC) * (check the footnote)
- Dacia Sandero B90 2008+
- Dacia Sandero 2010+ (BCM JC) * (check the footnote )
- Dacia Solenza 2003-2005
- Renault-Samsung SM3 2006+
- Renault-Samsung QM5
- Renault-Samsung SM3
- Renault-Samsung SM5
- Renault Fluence 2009+  * (check the footnote )
- Renault Fluence (BCM immobilzier) 2009+
- Renault Twingo Ph2 X06 2002-2007
- Renault Twingo II X44 2007+ 
- Opel Vivaro 2002-2006
- Opel Vivaro Ph2 2007+
- Opel Movano Ph2 2002-2006
- Opel Movano Ph3 2007+
- Opel Movano B 2010+
- Nissan Primestar Ph2 2002-2006
- Nissan Primestar Ph3 2007+
- Nissan Platina 2002-2008 
- Renault Latitude
- Renault Koleos

 

Prices of the special functions: 
RR004 - Odometer correction - - 192 euro

 

RR006 - Key learning - 1056 euro

 

FULL - all special functions - 1248 euro

Footnote ; * Programmer is also needed - ZN001 - TAG programmer  480 euro 

  Renault Key Programmer by OBD V2.5&V2.6

        NO PIN CODE NEEDED / NO PC NEEDED

                    

With Renault/Dacia/Opel/Nissan K-Line + CAN Key/Card Programming Device (Version 2.5) you will be able to program new keys or cards for Renault based vehicles via OBD-II socket which are
using Philips Cryto II(known as Hi Tag 2, ID46, PCF7936) transponder. Device is able to recognize type of the car automatically. There is no need to choose anything.
No more need of Immobilizer pin code as the device will read the pin code from the Immobilizer and will enter it directly.

Models covered:
- Megane II X84 2003-2006
- Renault Megane II Ph2 X84 2007+
- Renault Megane III X95 2009+
- Renault Scenic II X64 2003+
- Renault Scenic II Ph2 X64 2007+
- Renault Scenic III X95 2009+
- Renault Laguna II X56 2000-2005
- Renault Laguna II Ph2 X74 2005-2007
- Renault Laguna III X91 2007+
- Renault Valsatis X73 2002+
- Renault Valsatis Ph2 X73 2006+
- Renault Espace IV X81 2003-2006
- Renault Espace IV Ph2 X81 2006+
- Renault Master Ph2 X70 2002-2006
- Renault Master Ph3 X70 2007+
- Renault Traffic II X83 2002-2006
- Renault Traffic II Ph2 X83 2007+
- Renault Kango MUX Ph2 X76 2002-2007
- Renault Kango X61 2008+
- Renault Clio II Ph2/3 X65 2002-2006
- Renault Clio Symbol
- Renault Clio Thalia
- Renault Clio Campus
- Renault Clio Sedan
- Renault Clio Classic
- Renault Clio III 2005+
- Renault Clio III with key card
- Renault Modus 2004+
- Renault Grand Modus 2008+
- Renault Master III X62 2010+
- Dacia Duster 2010+ *
- Dacia Logan X90 2004-2008
- Dacia Logan Ph2 X90 2008+
- Dacia Sandero B90 2008+
- Dacia Solenza 2003-2005
- Renault-Samsung SM3 2006+
- Renault-Samsung QM5
- Renault-Samsung SM3
- Renault-Samsung SM5

- Renault Fluence 2009+ *
- Renault Fluence (BCM immobilzier) 2009+
- Renault Twingo Ph2 X06 2002-2007

- Renault Twingo II X44 2007+
- Opel Vivaro 2002-2006
- Opel Vivaro Ph2 2007+
- Opel Movano Ph2 2002-2006
- Opel Movano Ph3 2007+
- Opel Movano B 2010+
- Nissan Primestar Ph2 2002-2006
- Nissan Primestar Ph3 2007+
- Nissan Platina 2002-2008
- Renault Latitude
- Renault Koleo

  

 -Dacia Duster  needs V2.6 

 

 -Dacia Logan  needs V2.6 

- Dacia Sandero  need  V2.6 

  - Clio Symbol   needs V2.6 

 

  2010+ year with Johnson Control BCM module  this is new models that need TAG programmer with device

 

 

YOU CAN LEARN OR ADD MANY KEY / CARD TO THE CAR  NOT ONLY ONE  

AND THE ORIGINAL KEY/CARD REMAINS ACTIVE 

            COMMANDER FOR VOLVO  4.1

                      

Commander for VOLVO is software for diagnostic of VOLVO vehicles over CAN bus.

Full compatibility with VOLVO VIDA - DICE interface. Not only reprogramming. With AVDI are available full diagnostic options  

 

Standard diagnostic functions:

 

• For all electronic control units reading identification data
• For all electronic control units read error (DTCs)
• For all electronic control units clear error (DTCs)
• Device scan
• Data Display / Measured values

 

Special functions:

Mileage recalibration by OBDII in instrument cluster and CEM module - S40, V40, V50, S60, S80, V70, S80, XC60, XC80, XC90

Read/program internal EEPROM of the instrument cluster by OBDII - S40, V40, V50, S60, S80, V70, S80, XC60, XC80, XC90

 

Prices of the special functions: 

VL002 - Odometer correction - 480 euro

 

FULL - all special functions - 480 euro 

Note: Ordering of a special functions is possible only if you have our diagnostic interface AVDI

 

       

 

 

 

 

TOYOTA CAR LIST.pdf

COMMANDER  FOR TOYOTA / LEXUS / SCION VEHICLES  V5.0

ALL OTHER COMMANDERS SOFTWARE CAN BE ADDED  TO THE SAME AVDI

ALSO ORIGINAL SOFTWARES LIKE STAR DIAGNOSE /GT1.......

Full compatibility Toyota/Lexus/Scion OEM diagnostic software 

Toyota/Lexus/Scion Commander is a professional software for diagnostic of Toyota/Lexus/Scion vehicles. It allows you to perform complete diagnostics of all 1995-present Toyota/Lexus/Scion models. It provides some unique functions, which are not supported by any other diagnostic tool.

Standard diagnostic functions:
*Read fault codes
*Clear fault codes
*Device scan
*Display of Actual Values
*Actuator Tests
*Custom Read/Write

Special functions:

• Key Programming
  - provides ability for reset of immobilizer or smart system of the vehicle, registration of keys and remotes
• Transponder tool
  - programming key by dump of smart system/immobilizer, identification of transponders, cloning of ID67,ID68,ID70 and Texas fixed transponders, ability for preparation of ID67, ID68, ID70
• Dump tool
  - wide range of options for resetting (renew) of different units (immobilizers, smart systems, engine control modules, instrument clusters) by memory dump. Supported are also latest immobilizers with encrypted memory
• ID-box reset by LIN connection
• ECU flasher - available for EDC15, EDC16 engine control modules
• * Extended support of control units covered by functions Live Data, Active Tests, Coding
  * Extended supported immobilizer systems covered by "Key Programming" and "Key by Dump" functions - free for all owners of TN002
  

Prices of the special functions:
*TN002 - Key Programming, Transponder Tool, ID-box reset -  312 euro
*TN003 - Read/Write flash memory EDC16 - Free
*FULL - all special functions - 312 euro 

TOYOTA CAR LIST.pdf

Note: Ordering of special functions is possible only if you have our diagnostic interface AVDI 

  COMMANDER FOR CHRYSLER/ DODGE/ JEEP V2.6 

Commander Tool for Crysler, Dodge and Jeep is a software developed for  learning of keys and Mileage Recalibration of these vehicles. Basic diagnostics of all control units, including, but not limited to Engine, Instrument Panel Cluster, Skim, Electronic Transmission Control. Pin code extraction from SKIM dump for older vehicles. 

Standard diagnostic functions:

• Connect to the devices using KWP2000 and UDS over ISO transport protocol (CAN)
• For all electronic control units reading identification and extended identification information
• For all electronic control units read errors (DTCs)
• For all electronic control units clear errors (DTCs)
• Output tests
• Control unit adaptations - Seatbelt Warning Enable/Disable, Change mileage display between miles and kilometers and so on
• Actual values display
• Scan all units
• Clear all DTCs

 The key learning function works by CAN and J1850. see below the list of supported vehicles. In the next versions we will add more vehicles to this list FREE for all customers who owns the key learning function. Since version 2.3 we have added support for J1850 vehicles. Owners of the Chrysler Key Learning special function can read and write the FULL EEPROM of the Immobilizer control unit.

ALL OTHER COMMANDERS SOFTWARE CAN BE ADDED TO THE SAME AVDI
 ALSO ORIGINAL SOFTWARE LIKE STAR DIAGNOSE /GT1 ....

Supported Vehicles for key learning by OBDII:  

• Chrysler 300 (2006)
• Chrysler 300 (2007)
• Chrysler 300 (2010)
• Chrysler 300 (2011+) proximity keys
• Chrysler 300C (2005-2008)
• Chrysler 300C (2011+) proximity keys
• Chrysler 300M (-2007)- Requires J1850 Adaptor
• Chrysler 300M (2007)
• Chrysler Aspen (2007-2009)
• Chrysler PT Cruiser (-2006)- Requires J1850 Adaptor
• Chrysler PT Cruiser (2006-2010)
• Chrysler Sebring Convertible (2008)
• Chrysler Sebring (2003-2006)- Requires J1850 Adaptor
• Chrysler Sebring (2007-2008)
• Chrysler Neon- Requires J1850 Adaptor
• Dodge Avenger (2007-2011)
• Dodge Caliber (2007-2011)
• Dodge Caravan (-2007)- Requires J1850 Adaptor
• Dodge Caravan (2007-2010)
• Dodge Challenger (2008-2010)
• Dodge Challenger (2011+) proximity keys
• Dodge Charger (2006-2010)
• Dodge Charger (2011+) proximity keys
• Dodge Dakota (2005-2011)
• Dodge Durango Adv./SLT (2005)
• Dodge Durango (2001-2003)- Requires J1850 Adaptor
• Dodge Durango (2004-2009)
• Dodge Durango (2011+) proximity keys
• Dodge Grand Caravan Sport- Requires J1850 Adaptor
• Dodge Grand Caravan (2008-2009)
• Dodge Intrepid- Requires J1850 Adaptor
• Dodge Journey (2009-2011)
• Dodge Journey (2011+) proximity keys
• Dodge Magnum (2005)
• Dodge Magnum (2007)
• Dodge Neon (2005)
• Dodge Nitro (2007-2011)
• Dodge Pichup- Requires J1850 Adaptor
• Dodge RAM (-2006)- Requires J1850 Adaptor
• Dodge RAM 1500 (2006-2011)
• Dodge RAM 2500 (2006-2011)
• Dodge RAM 3500 (2006-2011)
• Dodge RAM (2007-2011)
• Dodge Ram (2011+) proximity keys
• Dodge Stratus- Requires J1850 Adaptor
• Jeep Commander (2006-2010)
• Jeep Grand Cherokee (2001-2005)- Requires J1850 Adaptor
• Jeep Grand Cherokee (2005-2011)
• Jeep Grand Cherokee (2011+) proximity keys
• Jeep Liberty (-2007)- Requires J1850 Adaptor
• Jeep Liberty (2008-2011)
• Jeep Compass (2007-2010)
• Jeep Patriot (2007-2011)
• Jeep Laredo (2007-2011)
• Jeep Wrangler Rubicon (-2007)- Requires J1850 Adaptor
• Jeep Wrangler (2007-2011)
• Plymouth Neon Highline (2001-2005)- Requires J1850 Adaptor
• Volkswagen Routan (2009-2012)

        COMMANDER FOR FORD V4.7

The Commander for Ford is a software intended for diagnostic of FORD vehicles over CAN bus. It provides abilities for IN code calculations, key programming and mileage recalibration.

ALL OTHER COMMANDERS SOFTWARES CAN BE ADDED TO THE SAME AVDI
 ALSO ORIGINAL SOFTWARES LIKE STAR DIAGNOSE /GT1 ....  

Standard diagnostic functions:

• For all electronic control units reading identification data
• For all electronic control units read error (DTCs)
• For all electronic control units clear error (DTCs)
• Device scan
• Data Display / Measured values

• Focus II 2004
• Transit Connect 2007+
• Transit 2006+
• Tourneo Connect
• Mondeo IV 2007+
• Fiesta V (CAN)
• Fiesta VI 2008+
• KA 2002-2008 (CAN)
• Galaxy III 2006+
• C-MAX
• Fusion
• S-MAX
• Kuga
• Mazda 2 2006+
• Mazda 3 2006+
• Mazda 6 2006+
• Explorer, Expedition, Ranger, Mariner, Mountaineer, F150, Fx50, Ex50 - 2005-2009
• Escape 2006-2011
• Edge, Flex 2006-2010
• Lincoln - MKS, MKX,MKT.MKZ 2006-2010

Mileage recalibration by OBDII

• Ford Focus II 2004+
• Transit Connect 2007+
• Tourneo Connect
• Mondeo IV High Line 2007+
• Fiesta (CAN)
• Galaxy III 2006+
• C-MAX
• Fusion
• S-MAX
• Kuga
• Crown Victoria 2006+
• Escape 2006+
• Flex 2006+
• E150-E350 2006+
• F150-F350 2006+
• Freestar 2006+
• Freestyle 2006+
• Mustang 2006+
• Edge
• Focus USA 2005+
• Fiesta USA 2010+
• Explorer 2004+
• Expedition 2004+
• Ranger 2004+
• Grand Marquis 2006+
• Town Car 2005+
• F150 2005+
• Fx50 2005+
• Ex50 2005+
• Flex 2007+
• Edge 2007+
• Fusion USA 2006+

Prices of the special functions: 
FR002 - InCode calculator + Key learning - 480 euro
FR003 - Odometer correction - 317 euro  

FULL - all special functions - 634  euro 

P.S : Ordering for special functions is possible only if you have our diagnostic interface AVDI

        COMMANDER FOR NISSAN V 4.1

                

Commander for Nissan is software intended for learning of keys of vehicles Nissan.

ALL OTHER COMMANDERS SOFTWARES CAN BE ADDED TO THE SAME AVDI
 ALSO ORIGINAL SOFTWARES LIKE STAR DIAGNOSE /GT1 .... 

 

Supported Immobilizer systems:

• Immobilizer NATS-2 Siemens - 5WK4593, 5WK4640, 5WK46472, 5WK4825, 5WK48642.
  NISSAN MICRA (K11) 1997 year 
  NISSAN Primera W/P10 1991-1996 year 
  NISSAN Maxima QX (A32) Schalter V 6 2,0ltr - 1995-2000 year
• Immobilizer NATS-4 Siemens - 5WK4738, 5WK4750, 5WK4803, 5WK48543A, 5WK48543B, 5WK48692.
  Extracting Immo Software Version, Read/Write eeprom from immo, Read Key Code, ADD Key, Delete Specific Key, Delete All Keys. 
  NISSAN Micra 1998-2000 year
  NISSAN Primera 2000-2003 year 
  NISSAN Almera 1998-2000 year
• Immobilizer NATS-5,NATS 5+ Siemens - 5WK48041, 5WK48042, 5WK48042, 5WK48643, 5WK48643, 5WK48644, 
  5WK48644, 5WK48644.
  Extracting Immo Software Version, Read/Write eeprom from immo, Read PIN Code, Check Key Status, ADD Key, Delete All Keys. 
  NISSAN Altima 2001-2004 year
  NISSAN Altima 2005 year
  NISSAN Armada 2004-2005 year
  INFINITI FX35/FX45 2004-2005 year
  INFINITI G20 2000-2002 year
  INFINITI G35 2003-2005 year
  INFINITI I30, I35 2000-2004 year
  INFINITI M45 2003-2005 year
  NISSAN Maxima 2000-2005 year
  NISSAN Murano 2003-2005 year
  NISSAN Pathfinder 2001-2005 year
  NISSAN Quest 2004-2005 year
  INFINITI QX4 2001-2004 year
  INFINITI Q45 2002-2004 year
  NISSAN Sentra 2000-2004 year
  NISSAN Titan 2004-2005 year
  NISSAN 350Z 2003-2005 year
  NISSAN Primera 2003 year
• Nissan Micra 2007+ *(check the footnote)
• Nissan Note 2006+ *(check the footnote)
• Nissan Tiida 2007+ * (check the footnote)
• Nissan Platina 2006+
• Nissan Kubistar 2007+
• Nissan Sunny 2006+
• Nissan Almera Classic 2006+
• Nissan Primestar/Interstar 2002-2006
• Nissan Primestar/Interstar 2007+ 

PIN Code CALCULATOR FOR ALL NEW BCM MODULES FOR INFINITY AND NISSAN CARS 2007-2012 FOR NORTH AMERICA, SOUTHAMERICA, ASIA, AUSTRALIA,MIDDLE EAST , BCM MODULES 5 DIGITS TO PIN 4 DIGITS  (EXAMPLE 12B3A=NEW CODE 4854/OLD CODE 3934)
WORKS FOR THESE CARS - ALTIMA SEDAN, ALTIMA COUPE, VERSA HATCHBACK, VERSA SEDAN,
CUBE, SENTRA, NISSAN LEAFT, MAXIMA, Z, Z ROADSTER, GTR, JUKE, ROUGE, MURANO, MURANO CROSS CABRIOLET XTERRA, PATHFINDER, ARMADA, QUEST, FRONTIER, TITAN, 370Z, XTRAIL, TIIDA, FRONTIER, MARCH,CIMA,FUGA,SKYLINE, LATIO,NEW TEANA, NEW SUNNY, PATROL, QASHQAI, DUALIS, FRONTIER, NAVARA, LIVINA, GRAND LIVINA, BLUEBIRD,G SEDAN, G COUPE, G CONVERTIBLE, INFINITY M, INFINITY EX, INFINITY EX, INFINITY FX, INFINITY JX, INFINITY QX

Prices of the special functions: 

NN003 - Key learning - 399 euro

NN004 - PIN Code Calculator new BCM 2007-2012 - 480 euro

 
FULL - all special functions - 879 euro

Note: Ordering for special functions is possible only if you have our diagnostic interface AVDI
 
Footnote : * Programmer is also needed - ZN001 - TAG programmer  480 euro 

 

               COMMANDER FOR MITSUBISHI  1.6

                                                 

       

Commander for Mitsubishi is a software intended for diagnostic and key programming for Mitsubishi vehicles.

Standard diagnostic functions: 

• For all electronic control units reading identification data
• For all electronic control units read/clear fault codes (DTCs)
• DTCs description is available in different languages - Czech, English, Finnish, French, German, Greek, Hebrew, Hungarian, Italian, Polish, Russian, Spanish, Turkish
• Device scan
• Data Display / Measured values
• Coding/Adaptations
• Output tests
• Read/Program flash Engine Control Units
• Output tests

Special Functions ;

• Key programming
• Dump tool

 The key programming function currently works by CAN.  check below the supported vehicles. In the next versions we will add more vehicles to this list FREE for all customers who owns the key learning function. We also plan to support vehicles with K-Line interface.
 Keys can be programmed when the pin code of the vehicle is known. The Mitsubishi Commander has a database of default pin codes. The pin code can be changed with the Mitsubishi Commander. If the pin code is changed - next time when a key is programmed the new pin code should be entered.

The Mitsubishi commander software supports all CAN vehicles for key programming by OBDII

• L200 (2006-2011)
• L200 Hunter (2011+)
• Hunter (2007-2011)
• Pajero (2006-2011)
• Grandis (2006-2011)
• Shogun (2006-2011)
• Montero (2006-2011)
• Eclipse (2006-2011)
• Galant (2006-2011
• Endeavor (2006-2011)
• Lancer (2007-2011)
• Lancer Evolution (2008-2011)
• Outlander (2007-2011)
• Colt (2006-2011) 
• Raider
• ASX
• Triton

The Dump Tool special function can be used to

• Modify odometer in EEPROM dump from dashboard
• Clear Crash Data from Airbag

Prices of the special functions: 

MI003 - EDC15 ECU - R/W eeprom and flash memory - 139 euro
MI004 - Key learning Advanced - 399 euro

FULL VERSION - all special functions - 557 euro  

Note: Ordering of special functions is possible only if you have our diagnostic interface AVDI

Note: Ordering of special functions is possible only if you have our diagnostic interface AVDI

    Ford Key Programmer device by OBDII

          NO PIN CODE NEEDED/NO PC NEEDED

              

Ford key programmer designed to program additional key into new Ford vehicles, even if you have all keys lost.

You can start your car or add new keys in few seconds by OBD .NO LAPTOP NEEDED !

Supported CAN based models from 2004

Models covered:
*Focus C170*, C170_SA, C307, C307_SA, C307_AP
*C-MAX C214
*Fiesta B256*, B376_AP
*Fiesta S.A. BV256*
*Fiesta B299 (2008y+)
*Ikon B376_AP*
*Fusion CD338, B226*
*Fusion B232 (2008y+)
*Galaxy/S-Max CD340
*Mondeo CD345
*Transit TRANSIT (2006y+)
*Transit Connect V227
*Tourneo Connect V227
*Mazda 3 MAZDA_3 (2006y+)
*Mazda 6 J61 (2006y+)
*Mazda CX-7 J31 (2006y+) 

KeyLess Go models:

*Fiesta B299 (2008y+)
*Fusion B232 (2008y+)
*Mondeo CD345 (2007y+)
*Galaxy/S-Max CD340 (2008y+) 

 

         Commander for Fiat/Lancia and Alfa 2.7

Commander for Fiat/Lancia/Alfa is software designed for odometer correction, key programming of Fiat vehicles. 

Standard diagnostic functions :

In this version of the software have been added several units. You can connect with them to Read and Clear DTC's.

Special functions:

Odometer correction by OBDII in instrument cluster of CAN based vehicles:

• Strada
  Fiat 500
  Alfa 147
  ALfa 159
  Lancia Y
  Alfa Mito
  Ford Ka 
  Idea
  Punto
  Grande Punto
  Panda
  Palio
  Linea
  Ducato 2006+
  Fiorino
  Albea
  Croma 2006+
  Doblo
  Lancia Musa 2006+
  Bravo 2005+
  Stilo 2001+
  Siena
  Maserati Quattro porte 2005, 2006

• Read/Write eeprom memory, Odometer correction by OBDII of Engine Control Unit - EDC15C5(EURO2), EDC15C7(EURO3). This model ECU has the following vehicles:
  Alfa 145 - 1.9 JTD
  Alfa 146 - 1.9 JTD 
  Alfa 147 - 1.9 JTD 16V ; 1.9 JTD 8V 
  Alfa 156 - 1.9 JTD ; 2.4 JTD 
  Alfa 166 - 2.4 JTD
  Fiat Bravo - 1.9 JTD 
  Fiat Brava - 1.9 JTD
  Fiat Doblo - 1.9 JTD
  Fiat Ducato - 2.0 JTD ; 2.3 JTD ; 3.8 JTD 
  Fiat Marea - 1.9 JTD ; 2.4 JTD 
  Fiat Marengo - 1.9 JTD
  Fiat Multipla - 1.9 JTD
  Fiat Punto - 1.9 JTD
  Fiat Palio - 1.9 JTD
  Fiat Stilo - 1.9 JTD
  Fiat Siena - 1.9 JTD
  Fiat Scudo - 2.0 JTD
  Lancia K - 1.9 JTD 
  Lancia Lybra - 1.9 JTD ; 2.4 JTD 
  Lancia Thesis - 2.4 JTD
  Lancia Z - 1.9 JTD
• Read/Write eeprom memory, Odometer correction, Make VIRGIN by OBDII of Engine Control Unit - Marelli Multijet MJD 6JF. This model ECU have the following vehicles:
  Fiat new Panda - 1.3 IAW Multijet MJD 6JF 
  Fiat Idea - 1.3 IAW Multijet MJD 6JF 
  Fiat Doblo - 1.3 IAW Multijet MJD 6JF
  Fiat Punto - 1.3 IAW Multijet MJD 6JF
  Fiat Grande Punto - 1.3 IAW Multijet MJD 6JF 
  Fiat Cinquecento - 1.3 IAW Multijet MJD 6JF
  Lancia Musa - 1.3 IAW Multijet MJD 6JF
  Lancia Ypsilon - 1.3 IAW Multijet MJD 6JF
• Read/Write Eeprom memory, Make VIRGIN by OBDII of Engine Control Unit - Marelli IAW 4AF/4EF/59F/5AF/5AM/5NF
• Read/Write Flash memory by OBDII of Engine Control Unit - Marelli IAW 4AF/4EF/59F/5AF/5NF/6JF; BOSCH ME7.3H4/ME7.3.1/ME7.2.1 ( BOOT MODE ) 
  MJD 6JF - IMMO OFF
• Change odometer of Engine Control Unit - BOSCH EDC16 - Tested Version for now : Fiat Croma, Alfa 159, Fiat 16, New Fiat Bravo 1.6 JTD, New Lancia Delta 1.6 JTD, Alfa GTV 1.9 JTD
• Transponder maker - Preparing transponder by dump of immobilizer to be ready for key programing.
• Key learning - by OBDII key programming for variuos models Fiat, Alfa, Lancia - Alfa 147, Mito; Fiat 500, Bravo, Grande punto, Croma, Doblo, Ducato, Fiorino, Idea, Palio, Panda, Stilo; Lancia Thesis, Delta 

    Commander for Hyundai and KIA V1.7

Commander for Hyundai and KIA is a software intended for progamming keys and diagnosing of these vehicles. Basic diagnostics of control units over CAN and K-Line - Engine, Instrument Panel Cluster, Immobilizer, Airbag, Electronic Transmission Control...
Display and clear fault codes. Display of DTCs in the following languages: English, French, Spanish, German, Italian, Russian, Czech, Polish, Bulgairan, Chinese, Turkish, Greek, Hungarian. 

Actuator tests - Fan speed actuation, lamps activation and so on. 

The key learning function works only by K-Line and CAN. The Hyundai/KIA Immobiliser system consists of the SMARTRA ECU which has its own CPU which controls the vehicles immobiliser in conjunction with the engine management ECU. The key learning function in general works for all Hyundai/KIA vehicles manufactured since year 2000 until today. check below the supported vehicles on which the key learning function is guranteed to work. In the next versions we will add more vehicles to this list FREE for all customers who owns the key learning function.

Key Learning by CAN and K-Line for the following models by OBDII

• KIA Morning
• KIA New Morning
• KIA Euro Start
• KIA Naza Suria
• KIA Naza Picanto
• KIA Ceed
• KIA Cerato
• KIA Carens
• KIA Soul
• KIA Picanto
• KIA Spectra
• KIA Sephia
• KIA Optima
• KIA Magentis
• KIA Rio
• KIA Venga
• KIA Forte
• KIA Opirus
• KIA Amanti
• KIA Cadenza
• KIA Sportage
• KIA Sorento
• KIA Mohave
• KIA Borrego
• KIA Rondo
• KIA Carnival
• KIA Sedona
• KIA Visto

• Hyundai Accent
• Hyundai Verna
• Hyundai Elantra
• Hyundai Avante
• Hyundai Sonata
• Hyundai Grandeur
• Hyundai H100
• Hyundai H200
• Hyundai SantaFe
• Hyundai Veracruz
• Hyundai Terracan
• Hyundai Tucson
• Hyundai Getz
• Hyundai Atos
• Dodge Atos
• Hyundai Santo Xing
• Hyundai i30
• Hyundai i20
• Hyundai i10
• Hyundai i800
• Hyundai Genesis
• Hyundai Equus
• Hyundai Porter
• Hyundai Libero
• Hyundai Entourage
• Hyundai Coupe

     Transponder/key programmer - ZN001 

This programmer works with AVDI interface. It also is compatible with our software  Commander for VAG, BMW, Renault, Nissan, Mercedes, Fiat.

Supported transponders:
 *Atmel TK5551 / T5
 o Temic 11
 o Temic 12
 o Megamos 13 (fixed identifier)
 o Megamos 48 (Megacrypt I)
 o Megamos 8E (Megacrypt II)
 o Texas TIRIS 4C
 o Texas TIRIS 4D 
 o Philips PIT - 7930/7931/7935 (PIT)
 o Philips HITAG2 – 7936, 7941, 7942, 7943, 7944, 7945, 7946, 7947, 7952, 7953, 7961
 o Philips HITAG-Pro – 7937, 7938, 7939, 7952 
 o JMA – TPX1 (cloning of Texas 4C)
 o JMA – TPX2 (cloning of Texas 4D/4E)
 Next software update consists : Texas 4E.

PRICE : ZN001 - TAG programmer - 480 euro

          ZN030 -ABPROG 

ZN030-ABPROG - This programmer works together with AVDI interface.- 288 euro

With the help of this programmer you can :

 - Read the SSID of the key, Erase the NEC chip and then program it again

With adapter ZN031* for M35xxx/SPI/I2C Adapter together with Abrites EEPROM Programmer software allows you to erase and write SPI EEPROM memory with and without incremental registers:

• M35080VP
• M35080V6
• D080D0WQ
• D160D0WQ
• M95080
• M95160
• M95320
• M95640
• M95128

            TAG KEY TOOL 5.5 

With this software you can program keys/transponders for vehicles, bikes or trucks from different brands that using Megamos 13, Megamos 48 (Megacrypt I), Megamos 8E (Megacrypt II), Texas 4C, Texas 4D, Temic 11, Temic 12, T5, TK5555, Philips PIT - 7930/7931/7935 (PIT), Philips HITAG2 – 7936, 7941, 7942, 7943, 7944, 7945, 7946, 7947, 7953, 7961, Hitag-Pro 7937, 7938, 7939, 7952 , JMA TPX1 and TPX2

This software is compatiable with AN020 and ZN001 transponder programmers. Just need dump from your immobilizer, put your NEW KEY (or transponder) on the programmer and generate working key! You can also produce preprogrammed transponders for a different vehicles.

*Utility for programming of key by dump of CAS4 - latest BMW Fx series. NO OTHER TOOL WITH SIMILAR OPTION

* Free transponder production ID67,ID68,ID70,TP22,TP23,TP24 ... and many others

*Big amount of utilities for programming of key by dump of immobilizer ( Fiat, Toyota, Ford, BMW, Audi/VW Kessy, Mercedes, Jeep, .. )

*Easy cloning of transpoders - Megamos 13, Temic 11/12, Philips ID33

*Easy cloning of Toyota/Lexus/Scion Texas TIRIS 4D transponders onto TPX2 transponder

*Easy cloning of ALL TYPES Texas 4D transponders onto TPX2 transponder - required internet connection

*Easy cloning of ALL TYPES Texas 4C transponders onto TPX1 transponder

*Programming of used BMW keys 7943/7944

PRICE : 

KT001 - TagKeyTool - Utility for programming of keys by dump of immo - 480 euro
KT005 - TagKeyTool - Utility for programming of TP22, TP23, TP24, TP25 from any Megamos 48 - free
KT006 - TagKeyTool - Key Maker for Passat B6/CC Keyless - 159 euro
KT007 - TagKeyTool - Key preparation by dump of CAS4 - 3840 euro

EXISTING OWNERS WHO HAVE BOUGHT AN020/ZN001 PROGRAMMERS BEFORE 20-SEP-2010 WILL RECIEVE FREE KT001

        MEGAMOS CRYPTO 48 TRANSPONDERS

TA2, TA3, TA4 and TA5 transponders are based on the Megamos 48 Crypto transponders
and can be used with the VAG Commander together with the TAG programmer (ZN001) for preparation of dealer keys from them. These transponders are suitable for the latest 2008+ models.
It is also possible to produce TP22, TP23, TP24 and TP25 transponders from the corresponding TA2, TA3, TA4 and TA5 transponders. 

No changes in the immobilizer/ECU are need.

*AUDI A3 - 2003+ (TA5 is used). The produced dealer key can be programmed then with standard key-learning procedure.

*AUDI A4 - 2003-2008 (TA5 is used). A4 from 2003 to 2008 are with BOSCH RB8 Instruments which require special key-learning procedure which is available in the VAG Commander.

*VW - 2005+ - For the models till 2008 (except Passat B6) it is needed only to have a TP23 transponder. 
This transponder can be produced from the TA3 transponder with the VAG Commander. 
For Passat B6 and remaining VW models 2008+ it is required to have a dealer key, which also is produced from the TA3 transponder with the VAG Commander.

*SEAT - 2005+ - For the models till 2008 it is needed only to have a TP22 transponder. 
This transponder can be produced from TA2 transponder with the VAG Commander.For the remaining Seat models 2008+ it is required to have a dealer key, which also is produced from the TA2 transponder with the VAG Commander. 

*SKODA - 2005+ - For the models till 2008 it is needed only to have a TP24 transponder. 

This transponder can be produced from theTA4 transponder with the VAG Commander.
For the remaining Skoda models 2008+ it is required to have a dealer key, which also is produced from the TA4 transponder with the VAG Commander.

Prices:
TA2/TA3/TA4/TA5 transponders on price of 5 EURO 

TP22/TP23/TP24/TP25 transponders on price of 5 EURO

 UNIVERSAL MERCEDES TRANSPONDER FOR E / C AND G CLASS 

This transponder is prepared to program directly to the car ,just insert the key into the ignition and the transponder will program itself immediately to start the car .
 each transponder has its own number from 1 to 8 so you can program up to 8 keys to the same car .
 price : 10 EURO
       

PCF 7935 & 7936 FOR BMW& MINI COOPER ARE AVAILABLE  - 5 euro /pc    

              IC PROGRAMMER 

 NEC programmer for Mercedes IR keys 

This programmer works together with AVDI interface. No need to disolder  NEC mcu from the key. Enough is to solder few wires.

 About data generation needed to be programmed in the key is useful to use Commander for Mercedes option MN005.

PRICE : ZN002 - NEC programmer - 240 euro

            IC / MCU programmer - AN022 

This programmer currently can be used together with your Commander for VAG to read and program Micronas MCU inside of instrument clusters from Volkswagen Audi Group vehicles.
 
 Using 3rd party software it supports:
 
 Read/Program EEPROM ICs - I2C, Mircrowire, SPI and other (M35080,...)
 Read/Program EEPROM/FLASH memory of Motorola MCUs from the family HC05,HC08,HC11,HC12,HCS12,9S12,MPC5xx
 Read/Program EEPROM/FLASH memory of Texas MCUs from the family TMS370,TMS374
 Read/Program EEPROM/FLASH memory of ST MCUs from the family ST7,ST10
 Read/Program EEPROM memory of National MCUs from the family CR16
 Read/Program EEPROM/FLASH Atmega MCUs
 Read/Program EEPROM/FLASH memory of ARM MCUs from the family Micronas CDC32xxG
 Programmer can skip read protection security of the following MCUs - HC05B, HC05X, HC11EA9, HC11E9, HC12,HCS12,9S12 

Programmer including some additional adapters : TMS MCUs, ARM JTAG, Mororola BDM, HC05..

PRICE : AN022 - IC/MCU programmer - 240 euro 

          SAE J2534 (PassThru) compliant driver for AVDI

Using this driver your AVDI interface will become compliant to SAE J2534-1 
Connected through high speed USB 2.0 or Bluetooth it can be used to perform online diagnostics or ECU reprogramming of a wide range of vehicles. It can be used also like Vehicle Communication Interface with many 3rd party software like:

*Honda HDS
*Volvo VIDA (full diagnostic capabilities)
*Toyota/Lexus/Scion Techstream
*Mercedes Star Diagnose (only CAN Bus)
*Rover/Jaguar IDS
*Ford Scanner 
*Chrysler J2534 Flash Application  ... etc ..... 

Each SAE J2534 compliant interface can be used to access manufacturer’s reprogramming web site and to update software of electronic control units in the vehicle.     

Current driver software version is 2.0

Supported bus protocols:

- CAN - GMLAN, ISO14229, ISO15765, J1939 - two CAN channel switchable single/dual wire
- KWP2000 (ISO9141, ISO14230)
- J1850, J2610 – under development

Other features:
- A/D input
- Switching CAN bus and K-line on different PINs

Click here to know more about J2534 and ECU reprogramming 

Free software updates of the driver!

Driver is included in the package with AVDI interface.

CLICK HERE TO GET AN ONLINE ACCESS TO ECU REPROGRAMMING AND DIAGNOSTIC .SAE J2534 MANUFACTURERS  ONLINE